Clik here to view.
Incorrect DH87MC SATA Identification on either the mobo or within the visual...
Looking at the DH87MC motherboard, the SATA connections are numbered "SATA 6G 0" through "SATA 6G 4".The DH87MC mobo diagram below, shows the layout and naming convention. This is also how it is...
View Articleproblem with BT and WIFI WIN8.1 N7260
hi there,i am getting really frustrated, i have a new dell inspiron with win8.1 and i have 2 major problems that are really getting me frustrated.befor i start i will say that i tried to use dell's...
View ArticleDH87MC: How to add UEFI boot entry for Linux?
Hi all, I'm trying to install Linux on this motherboard using UEFI boot only, and while it can boot Linux in UEFI mode from a USB stick, I can't figure out how to get it to boot from my hard disk...
View ArticleHow to enable the Yocto-provided package management capability
As some of you may know, the Linux image you create after following the BSP Build Guide is not the only result of the process.It also builds a lot of additional software packages, only some of which...
View ArticleGPIO pin goes high on reboot of Galileo board?
I'm working on a robotics application and the GPIO Pin is going high momentarily when the Galileo board reboots,Is there a way this behavior can be changed? -Simon.
View ArticleClik here to view.
DN2820FYKH : What is this USB dongle in the product page?
https://www-ssl.intel.com/content/www/us/en/nuc/nuc-board-dn2820fykh.html I saw this USB dongle beside the NUC DN2820FYKH unit. However, it doesn't seem to come together with the package (correct me if...
View ArticleNew Intel NUC Kit DN2820FYKH
The new Celeron NUC looks like an excellent product: http://www.intel.com/content/www/us/en/nuc/nuc-board-dn2820fykh.html The always loaded question, when might it be available at retail? Is it...
View ArticleGalileo Board - no USB cable, no booklet, no standoff separators and screws,...
Hi,I was quite surprised to find there are boxes which come with no USB cable inside. If you go on YouTube and look for 'unboxing Galileo' you will see some boxes get a blue man inside and all the...
View Articlegraphic communication via PCIe
How do I setthegraphic communicationisvia serial portbutusingPCIe? I boughtthe graphics cardMPX-750 monitor isconnectedI've notattothat the graphics cardgetssignalbutnotfromGUImonitoroutput. You need...
View ArticleDQ77MK: USB and network failures under Win7, unable to flash BIOS
System specifications:Windows 7 SP1 Professional x64Intel DQ77MK motherboardIntel Core i5-3570 processor (not the K model, as I require the virtualisation features) (passes Intel's processor diagnostic...
View ArticleNew NUC DN2820FYKH - Several Issues
I purchased a couple of the DN2820FYKH NUC's to use as HTPC's, which much to my excitement arrived yesterday.Unfortunately my excitement was short lived when I couldn't enter the BIOS by pressing F2...
View ArticleClik here to view.
(Moderator can you read plz) Intel(R) HD graphics --- Inspiron N5010
Hi moderator, I just want to know if you think to upgrade some part of the Intel(R) HD graphics to have better OpenGL than version 2.1 and have a better Intel HD control panel to modify AA (have to...
View ArticleESRT 2 SATA & SAS SOFTWARE RAID DRIVE
Hi!ESRT 2 SATA & SAS SOFTWARE RAID DRIVE how can i install on bios, since i reformat a hard drive and install a new windows server 2008, when i came to bios set up and enable the mass storage to...
View ArticleClik here to view.
BSoD / Intel NUC D54250WYK + Haswell Graphics Drivers 6.14.10.5445
I installed Windows XP SP3 in D54250WYK.I could install almost drivers excepted the Display Driver.I installed XP Haswell Graphic driver 6.14.10.5441 and 6.14.10.5445, but it shows BSoD after reboot....
View ArticleHow can I get the source of Arudino IDE for galileo
Hi guys.I want to ask how can I get the source of Arudino IDE for galileo ?Andi What should I do to build the Arduino IDE source for x86-linux or arm-linux?Any help will be appreciated.
View ArticleHaswell NUC - No Signal when switching source
Hi All, I'm having a problem with my D34010WYK i3 Haswell NUC. I am currently running OpenELEC on the NUC, but the issue is not an OS problem, as it also occurs in BIOS (as well as Windows 7 for the...
View ArticleCan I make a USB3.0 class driver for Windows 7 with WDK8.1 ?
Hi, I'm planning to make a USB3.0 class driver(KMDF) with WDK8.1 for my PC that has an Intel Chipset. details of my PC:Model: DELL Optiplex 9020OS: Windows 7 Professional 32bit SP1Chipset: Intel Q87...
View ArticleNew D54250WYKH build drive questions
First, I have not built a computer before, thus this may be a rookie question, but I need some input. Here is what I have done. I have assembled an D54250 tall unit with 2 drives, wifi card, and...
View ArticleLinux Standard Base (LSB) Image doesn’t boot on Galileo
Hi everybody,I’ve followed the tutorial in order to build a Linux Standard Base Image (http://www.malinov.com/Home/sergey-s-blog/intelgalileo-buildinglinuximage ), generated the files I need, I renamed...
View ArticleCannot connect my Galaxy S3 to my PTV2000
I have been trying to connect my Galaxy S3 to my PTV2000 adapter using the Screen Mirroring feature on my S3. It does connect when I try and I can hear audio but no video, this will only last for...
View Article